Thank you for choosing Superloop network, we understand setting up BYO modem can be a bit difficult and are happy to provide whatever support required. Below is the step-by-step guide for your support on ASUS modem setup.
This guide is For FTTN | FTTB services only.
Note: The maximum speed plan you can get on FTTN and FTTB is up to 100Mbps.
Please connect your modem to the main DSL socket (Telephone socket) of your premises via the DSL port of your modem using a DSL/Telephone cable.
For how to setup your fibre device connection please click here.
Setting up your Router
- Ensure the Router is turned on and plugged into Power.
You should see a SOLID Green/Blue Light on top of the Power Icon
- Plug the Modem Router into the DSL/Telephone Socket using a Working DSL/Telephone Cable
You plug in the Telephone/DSL cable from the DSL port on the Modem Router to the NBN DSL Telephone Socket
The port might also be labelled as:
- DSL
- VDSL
- INTERNET
- Connect to your Modem Router using Wi-Fi
Locate the SSID and Wi-Fi Pin/Password on the bottom of the device. Use these details to locate the Wi-Fi name on your computer and then join the network.
When you successfully join the network, it will says “No Internet, Secured”. This means your device is connected to the Modem Router’s Wi-Fi network but there is no internet connection as the device has not been set-up/configured.
Please perform the below-mentioned steps to configure your modem: -
1. Connect your Laptop/PC/Tablet/Mobile to the Wi-Fi of your modem or via LAN cable connection if available.
(Note: It is not necessary to be connected to the internet to do this)
2. Open an Internet browser. (E.g.:- Chrome, Safari, Edge)
3. Log into your Modem Gateway
a) Type asusrouter.com or router.asus.com or 192.168.1.1 in the Address bar of your browser
(Note: If hyperlink or IP address does not work, check your modem for the correct hyperlink or IP address)
4. When prompted for Username and Password, by default
- Username: - admin
- Password: - admin
(Note: If Username/Password did not work, please check back of your modem for correct Username/Password)
Once logged in, you may come across 1 of the following interface variants depending on the model and firmware of your Asus modem.
Variant 1: -
1. Once logged in, it will redirect to a Quick Settings section.
Generally, your Asus Router will Auto detect the connection and would take you to the Wi-Fi configuration settings.
But in the event, it doesn’t automatically configure, please follow the instruction below.
2. Select “Advanced Settings”
3. Select “Choose Operation Mode”
4. Select “Wireless Router Mode” or select “DSL Router Mode” if available.
2. Now under “Internet Connection Type” select Automatic IP or Dynamic IP
- Leave VLAN ID Unchecked if present.
- (Note: If you come across different other settings, please leave them in default)
3. Configure your Wireless Settings (This includes Wi-FI Name and Wi-FI Password)
4. You can simply Click "Next" to the next set of Settings and Click “Apply” to finalize your Configuration.
On successful configuration, your modem will go online within 2-4 minutes.
Please test the service once done.
Variant 2: -
1. Once logged in, it may directly take to configuration panel. Go to “Advanced Settings” > Select “WAN”
2. Now under “Internet Connection” tab
- WAN type: - “DSL” / “VDSL WAN (PTM)”
- WAN Connection Type: - “Dynamic IP” / “Automatic IP”
- Do not Clone MAC Address if available.
- Leave “VLAN ID” unchecked or turn it off if present.
- (Note: If you come across different other settings, please leave them in default)
- Click “Apply”
On successful configuration, your modem will go online within 2-4 minutes.
Please test the service once done.
If you needed further assistance with your modem configuration, please contact your modem manufacturer.