D-Link Modem DSL/VDSL Service Configuration
For FTTN | FTTB (Superloop)
Note: The maximum speed plan you can get on FTTN and FTTB is up to 100Mbps.
Please connect your modem to the main DSL socket (Telephone socket) of your premises via the DSL port of your modem using a DSL/Telephone cable.
Setting Up A Router
- Ensure the Router is turned on and plugged into Power.
You should see a SOLID Green Light on top of the Power Icon
- Plug the Modem Router into the DSL/Telephone Socket using a Working DSL/Telephone Cable
You plug in the Telephone/DSL cable from the DSL port on the Modem Router to the NBN DSL Telephone Socket
The port might also be labelled as:
- DSL
- VDSL
- INTERNET
- Connect to your Modem Router using Wi-Fi
Locate the SSID and Wi-Fi Pin/Password on the bottom of the device. Use these details to locate the Wi-Fi name on your computer and then join the network.
When you successfully join the network, it will says “No Internet, Secured”. This means your device is connected to the Modem Router’s Wi-Fi network but there is no internet connection as the device has not been set-up/configured.
Please perform the below-mentioned steps to configure your modem: -
1. Connect your Laptop/PC/Tablet/Mobile to the Wi-Fi of your modem or via LAN cable connection if available.
(Note: It is not necessary to be connected to the internet to do this)
2. Open an Internet browser. (E.g:- Chrome, Safari, Edge)
3. Log into your Modem Gateway
(Note: If hyperlink or IP address does not work, check your modem for the correct hyperlink or IP address)
4. When prompted for Username and Password, by default
- Username: - admin
- Password: - admin
(Note: If Username/Password did not work, please check back of your modem for correct Username/Password)
Once Logged in, You may come across 1 of the following Interface Variants depending on the Model and Firmware of your D-Link modem.
Variant 1:-
- Once logged in, if it’s the first time configuring this modem, then, it will take you to a quick setup window > click “next” to start setup.
- Once you are in “ISP Settings” window,
- Select “Wan Access Type” > “VDSL”.
- Select your country.
- Select ISP as “Other”.
(Note: Keep other settings in default)
- Under “Configure your internet connection” window > Select “Dynamic IP Address”.
Sometimes this option may be displayed in the following format, in this case, select “DHCP Connection (Dynamic IP)”
- Now click “Next” Until you move to the last page to save the settings.
(Note: If you come across different other settings, please leave them in default)
- Click “Apply” to save the settings.
- On successful configuration, your modem will go online within 2-4 minutes.
Please test the service once done.
Variant 2:-
- Once logged in, Go to “Settings” > “Internet”.
-
- Select “WAN Connection Type” > “VDSL”.
- Select “Service Number” > “Add” to create a service connection.
- ENABLE VIRTUAL CIRCUIT <<<<< (BUT DO NOT ENABLE VLAN or ENTER ANY VLAN ID)
- Under “WAN Settings”,
-
- Select “Connection Type” > “Dynamic IP (DHCP)”.
- “WAN Service Type” > “Internet”.
- You may keep “IP Control” in “Dynamic”. (If you come across this setting)
- Set “Connect mode select” to “Always On”. (If you come across this setting)
- Leave VLAN Unchecked/Blank (If you come across this setting)
(Note: If you come across different other settings, please leave them in default)
- Click “Apply”
- On successful configuration, your modem will go online within 2-4 minutes.
Please test the service once done.
Variant 3:-
- Once logged in, Go to “Settings” > “Internet”
- Select “My Internet Connection is” > “Dynamic IP (DHCP)”.
- You may keep “Address mode” in “Dynamic IP”.
-
- Leave VLAN Unchecked/Blank (If you come across this setting)
(Note: If you come across different other settings, please leave them in default)
- Click “Save”
- On successful configuration, your modem will go online within 2-4 minutes.
Please test the service once done.
If you needed further assistance with your modem configuration, please contact your modem manufacturer.